Steve,
This is general reply. Besides the VIS board issue, you may also try to
re-seat all the boards in the computer.
Renato
-----Mensagem original-----
De: Confocal Microscopy List [mailto:[log in to unmask]] Em
nome de George Ring
Enviada em: quarta-feira, 4 de março de 2009 15:52
Para: [log in to unmask]
Assunto: Re: MRC 1024 question
Steve,
First of all, I have no idea what is causing your problem. You seem to have
adopted the rule of thumb "When in doubt, reboot". With a different problem
that we've experienced on our MRC1024, we found that rebooting wasn't
sufficient. In order to "reboot" the system, we have to physically unplug
the control tower. Even when it is off, it is still receiving power and
doesn't reset by simply switching it off.
Good luck,
George
George Ring, Ph.D.
Dept. of Cell and Developmental Biology
SUNY Upstate Medical University
750 E. Adams St.
Syracuse NY 13210
Tel. (315) 464-8595
FAX (315) 464-8535
email: [log in to unmask]
>>> On Wed, Mar 4, 2009 at 1:38 PM, in message
<[log in to unmask]>, "Stephen C. Kempf"
<[log in to unmask]> wrote:
> Tom,
>
> I wish it was that simple. The system is running with the scanning
> software (not emulation) and one of my students just told me that it
> happened in the middle of a scan that was progressing normally the
> other day. Seems to me like it might be a hardware problem.
>
> Steve
>
> On Mar 4, 2009, at 10:57 AM, Moninger, Thomas wrote:
>
>> Steve,
>>
>> Well, let*s check the easiest possibility first. Could it be that the
>> software is occasionally being started in the *No hardware* or
>> emulation mode? What you describe is exactly what happens when you
>> try to scan in emulation mode.
>>
>> Tom
>>
>> Notice: This UI Health Care e-mail (including attachments) is covered
>> by the Electronic Communications Privacy Act, 18 U.S.C.
>> 2510-2521, is confidential and may be legally privileged. If you are
>> not the intended recipient, you are hereby notified that any
>> retention, dissemination, distribution, or copying of this
>> communication is strictly prohibited. Please reply to the sender
>> that you have received the message in error, then delete it. Thank
>> you.
>>
>> From: Confocal Microscopy List
>> [mailto:[log in to unmask]] On Behalf Of Stephen C.
>> Kempf
>> Sent: Wednesday, March 04, 2009 10:44 AM
>> To: [log in to unmask]
>> Subject: MRC 1024 question
>>
>> We're having a problem with our BioRad MRC 1024 confocal that I hope
>> someone else on this list has experienced and resolved. When using
>> the scope a week or so ago, it stopped producing images and started
>> giving solid green, red or blue scans on the various channels. A few
>> days later, one of my other students used it and it was working
>> properly again. Then this weekend, we got the solid green, red or
>> blue scans again. We tried various changes in settings, different
>> accounts, different methods, retarting the software, and restarting
>> the system, but to no avail. Can any one offer some insight as to
>> what the problem might be?
>>
>> Thank you,
>>
>> Steve Kempf
>> _____________________________________________________________________
>> _
>> ________
>> Stephen C.
>> Kempf
>> E-mail: [log in to unmask] Associate
>> Professor
>> Tel: 334-844-3924
>> Faculty Director, AU Hybridoma Facility
>> Cell: 334-703-6689
>> Department of Biological Sciences
>> Fax: 334-844-9234
>> 331 Funchess Hall
>> Auburn University, AL 36849
>> Lab Web site - http://www.auburn.edu/cosam/departments/biology/
>> faculty/webpages/kempf/index.htm
>> Course web sites:
>> Vert. Dev. - http://www.auburn.edu/academic/classes/zy/
>> vert_embryo/index_vert_embryo.html
>> Histology - http://www.auburn.edu/academic/classes/zy/hist0509/
>> index_histology.html
>>
>>
>>
>>
|
